ROHDE & SCHWARZ SMP02 REPAIR and ROHDE & SCHWARZ SMP02 CALIBRATION
 
Custom-Cal has a high success rate in the repair of the ROHDE & SCHWARZ SMP02. A calibration by Custom-Cal is performed by engineers with extensive OEM experience. We have the expertise and the necessary standards to perform the ROHDE & SCHWARZ SMP02 Calibration, onsite calibration may be available. We specialize in quick turnaround times and we can handle expedited deliveries upon request.

Need another Signal Generator?
Shop for Comparable Products on our  used Signal Generator page

 
   ROHDE & SCHWARZ SMP02 (1035.5005.02)   Description / Specification:   Spec Sheet 
ROHDE & SCHWARZ SMP02 20 GHz Microwave Signal Generator

The R&S SMP02 (1035.5005.02) 20 GHz Microwave Signal Generator has been designed for high output power with AM, FM and optional phase modulation. High spectral purity is ensured by the use of YIG oscillators – up to 20 GHz without any frequency multiplying. The crystal reference built-in as standard ensures an accurate and low-drift output frequency. The SMP02 has extremely low SSB phase noise of <–105 dBc/Hz at 10 GHz (10 kHz from carrier) as well as nonharmonics of <–60/54 dBc up to/above 20 GHz. Functions qualifying the SMP02 for EMC applications include the trigger facility for step-by-step sweeping, marker outputs and, above all, the extension of the frequency range to 10 MHz (option SMP-B11). Specifications. Frequency Range: 2 GHz to 20 GHz. Resolution: 0.1 Hz. Setting time (to within <1x10^–6) after IEC-/IEEE-bus delimiter: <(11 ms + 5 ms/GHz). Phase offset: adjustable in 1° steps. Harmonics f <1.8 GHz: <–30 dBc (<+8 dBm). Nonharmonics at >10 kHz from carrier f <2 GHz: <–60 dBc typ. Maximum level: >+17 dBm (10MHz to <2GHz), >+11.5 dBm (2 GHz to 20 GHz). Resolution: 0.1 dB or 0.01 dB. Output impedance: 50 ohm. Remote control: IEC625 (IEEE488). Options. SMP-B11 (1036.6240.02), Frequency Extension 0.01 GHz to 2 GHz. SMP-B12 (1036.5750.02), Pulse Modulator 2 GHz to 20 GHz. SMP-B13 (1036.7147.02), 0.01 GHz to 2 GHz. SMP-B14 (1036.7347.02), Pulse Generator. SMP-B15 (036.5250.02), RF Attenuator 27 GHz. SMP-B18 (1036.8920.02), Auxiliary Interface. SMP-B19 (1039.4303.02), Rear Connectors for RF, AF. SMP-B1 (1036.5109.02), OCXO Reference Oscillator. SM-B2 (1036.7947.02), LF Generator. SM-B5 (1036.8489.02), FM/phaseM Modulator.



 

Standard Calibration $635.00 *
Click on Logo for More Prices
*This is a Web introductory price for one calibration of the ROHDE & SCHWARZ SMP02. Price does not in most cases include measurement performance data. Pricing does include NIST traceable calibration and issue of a calibration certificate and calibration label. Pricing may vary slightly due to volume and location of laboratory supporting calibration. Volume pricing may apply. On-site fees may apply depending on logistics, location and volume of work to be completed during the visit.


Related Bench Equipment Terms and Definitions. For a complete list go to our  Terms and Definitions Page.

dBm
dBm (sometimes dBmW) is an abbreviation for the power ratio in decibels (dB) of the measured power referenced to one milliwatt (mW). Zero dBm equals one milliwatt. A 3 dB increase represents roughly doubling the power, a 3 dB decrease, the power is reduced by about one half.

Millimeter-wave
Millimeter-wave is a term that generally refers to frequencies of 26.5 GHz and above. That is where signal wavelengths fall below approximately 10 mm, and thus the terminology changes from centimeters to millimeters.

Power Repeatability
Power Repeatability is the random uncertainty in reproducing the power level after changing and re-setting the power level. The power repeatability is ± half the span (in dB) between the highest and lowest actual power. Note: - The long-term power repeatability can be obtained by taken the power repeatability and power stability into account.

Stability
Stability is the extent to which a specified property, characteristic, or parameter of a substance, device, or apparatus, remains fixed with the passage of time or with varying environmental conditions.

Please contact us for your ROHDE & SCHWARZ SMP02 REPAIR and/or ROHDE & SCHWARZ SMP02 20 GHz Microwave Signal Generator CALIBRATION
I'm interested in: 
Calibration Type (Select one):
Repair Information:
 Serial Number:

 Is there any physical damage?  
 If yes, describe:


What is the description of the problem?

How/when did the problem start?


 (*) Required Fields    For formal quote please fill in all fields.
Company:
From (Email):*
Contact Name:*
Country:*
Address 1:
Address 2:
City:
State/Territory/Province: *
Zip/Postal Code:
Phone:*

Comment: