TEKTRONIX 11A34 CALIBRATION and TEKTRONIX 11A34 REPAIR

 
A calibration by Custom-Cal is performed by engineers with extensive OEM experience. We have the expertise and the necessary standards to perform the TEKTRONIX 11A34 Calibration, onsite calibration may be available. We specialize in quick turnaround times and we can handle expedited deliveries upon request.

Need another Oscilloscope Plug In?
Shop for Comparable Products on our
 used Oscilloscope Plug In page

 
   TEKTRONIX 11A34   Description / Specification:    
TEKTRONIX 11A34 4-Ch High Impedance Amplifier Plug-in

Four channel, High Impedance, amplifier plug-in for the 11000 Series and DSA 600A Series mainframes. Offers switchable 1 M-ohm/50 ohm input impedance. Bandwidth (Max) - 300 MHz. Calibrated Deflection Factors - Coarse steps: 1 mV to 10 V/div in 1-2-5 sequence Fine steps: Between coarse steps in 1 % increments of next more-sensitive coarse step. Accuracy - delta Volts DC accuracy: With 11400: ± (0.9% + 0.012 div). With DSA 600: ± (10% + 0.02 div). DC Balance, 1 to 99.5 mV/div: ± (1.0 mV + 0.10 div). Offset Accuracy, 1 to 99.5 mV/div (± 1 V range): (± 0.2% + 0.5 mV). For absolute DC accuracy of single-point measurements using offset, add the Offset Accuracy and DC Balance terms. Offset Range - 1 to 99.5 mV/div: ± 1 V; Resolution: 25 uV. 100 mV to 0.995 V/div: ± 10 V; Resolution: 250 uV. 1 to 10 V/div: ± 100 V; Resolution: 2.5 mV. Overdrive Recovery -1 to 99.5 mV/div: To within ±(0.3% +0.2 div) within 50 ns from ±2 V step. 100 to 995 mV/div: To within ± 1 % within 50 ns from ±20 V step. 1 to 10 V/div: To within ± 1 % within 50 ns from ±200 V step. Typical Noise (RMS) - 1 to 1.99 mV/div: 0.12 div. 2 to 4.98 mV/div: 0.06 div. 5 to 9.95 mV/div: 0.025 div. 10 mV to 10 V/div: 0.014 div. Input Impedance - Switchable: 1 M-ohm in parallel with 15 pF, or 50 ohm ±0.5% Input Coupling Modes - AC, DC, and OFF. AC Coupled Low Frequency; -3 dB point, driven from 50 ohm source: less than 10Hz. Maximum Input Voltage - 1 M-ohm mode: 500 V (DC + peak AC). 50 ohm mode: The input impedance is switched to 1 M-ohm when the input signal exceeds safe limits. Manual reset by re-selecting 50 ohm input impedance.



 

Standard Calibration $285.00 *
Click on Logo for More Prices
*This is a Web introductory price for one calibration of the TEKTRONIX 11A34. Price does not in most cases include measurement performance data. Pricing does include NIST traceable calibration and issue of a calibration certificate and calibration label. Pricing may vary slightly due to volume and location of laboratory supporting calibration. Volume pricing may apply. On-site fees may apply depending on logistics, location and volume of work to be completed during the visit.


Related Bench Equipment Terms and Definitions. For a complete list go to our  Terms and Definitions Page.

dBc
dBc (decibels relative to the carrier) is the power ratio of a signal to a carrier signal, expressed in decibels. If the dBc figure is positive, then the relative signal strength is greater than the carrier signal strength. If the dBc figure is negative, then the relative signal strength is less than carrier signal strength.

Load Regulation
Load regulation is the capability to maintain a constant voltage (or current) level on the output channel of a power supply despite changes in the supply's load (such as a change in resistance value connected across the supply output).

Power Linearity
When changing the power level and measuring the differences (in dB) between actual and displayed power levels, the power linearity is ± half the span (in dB) between the maximum and the minimum value of all differences.

Settling Time
Settling time of an output device is the time elapsed from the application of an ideal instantaneous step input to the time at which the amplifier output has entered and remained within a specified error band, usually symmetrical about the final value.


Please contact us for your TEKTRONIX 11A34 CALIBRATION and/or TEKTRONIX 11A34 4-Ch High Impedance Amplifier Plug-in REPAIR

I'm interested in: 
Calibration Type (Select one):
 (*) Required Fields    For formal quote please fill in all fields.
Company:
From (Email):*
Contact Name:*
Country:*
Address 1:
Address 2:
City:
State/Territory/Province:
Zip/Postal Code:
Phone:*

Comment: