AEROFLEX-IFR 2390A CALIBRATION and AEROFLEX-IFR 2390A REPAIR
 
A calibration by Custom-Cal is performed by engineers with extensive OEM experience. We have the expertise and the necessary standards to perform the AEROFLEX-IFR 2390A Calibration, onsite calibration may be available. We specialize in quick turnaround times and we can handle expedited deliveries upon request.

Need another RF Spectrum Analyzer?
Shop for Comparable Products on our  used RF Spectrum Analyzer page or new RF Spectrum Analyzer page

 
   AEROFLEX-IFR 2390A   Description / Specification:   Spec Sheet 
AEROFLEX-IFR 2390A 22 GHz Spectrum Analyzer

The Aeroflex-IFR 2390A 22 GHz Spectrum Analyzer is fully synthesized to give accurate frequency measurements. Even on wide spans the 2390A gives precise frequency measurements and an integral frequency counter enables the measurement of individual signals to 1 Hz resolution. The 2390A has resolution bandwidths down to 3 Hz. Narrow resolution bandwidths provide the ability to resolve closely spaced signals or sidebands. The 3 Hz filter is also used for close in signal analysis, for example it can be used to identify 50 or 60 Hz power line sidebands on oscillators. The average displayed noise level when using a 3 Hz filter is less than -135 dBm at 2.9 GHz and below -125 dBm at 22 GHz. The 2390A features built-in receivers for both AM and FM signals. Modulation detection can be set to narrowband or wideband mode. For an FM transmission a modulation scale of 1 kHz to 5 MHz per division allows direct measurement of the modulation component of carrier signals up to ±20 MHz deviation. The 2390A can be used for precompliance testing of electronic products to meet stringent EMC specifications. Specifications. Frequency Range: 9 kHz to 22 GHz. External Mixing 3 GHz to 300 GHz. Frequency Readout Accuracy: ± (3% of Span Width + Frequency Standard Accuracy + 50 % of RBW). Frequency Span Range: 10 Hz/div to 2.2 GHz/div. Accuracy: ± 5% of indicated span. Sweep Span > 200 HZ/div: 1 ms to 10 s/div in 1-2·5 sequence. Options. Option 02, Tracking Generator. Option 08, Quasi-Peak Detector.



 

Standard Calibration $540.00 *
Click on Logo for More Prices
*This is a Web introductory price for one calibration of the AEROFLEX-IFR 2390A. Price does not in most cases include measurement performance data. Pricing does include NIST traceable calibration and issue of a calibration certificate and calibration label. Pricing may vary slightly due to volume and location of laboratory supporting calibration. Volume pricing may apply. On-site fees may apply depending on logistics, location and volume of work to be completed during the visit.


Related RF Terms and Definitions. For a complete list go to our  Terms and Definitions Page.

dBm
dBm (sometimes dBmW) is an abbreviation for the power ratio in decibels (dB) of the measured power referenced to one milliwatt (mW). Zero dBm equals one milliwatt. A 3 dB increase represents roughly doubling the power, a 3 dB decrease, the power is reduced by about one half.

Noise Figure
Noise Figure the ratio of the signal-to-noise power ratio at the input to the signal-to-noise power ratio at the output.

Standing Wave Ratio (SWR)
Standing wave ratio (SWR) is the ratio of the amplitude of a partial standing wave at an antinode (maximum) to the amplitude at an adjacent node (minimum).

Please contact us for your AEROFLEX-IFR 2390A CALIBRATION and/or AEROFLEX-IFR 2390A 22 GHz Spectrum Analyzer REPAIR
I'm interested in: 
Calibration Type (Select one):
Repair Information:
 Serial Number:

 Is there any physical damage?  
 If yes, describe:


What is the description of the problem?

How/when did the problem start?


 (*) Required Fields    For formal quote please fill in all fields.
Company:
From (Email):*
Contact Name:*
Country:*
Address 1:
Address 2:
City:
State/Territory/Province: *
Zip/Postal Code:
Phone:*

Comment: