ROHDE & SCHWARZ SMR30 CALIBRATION and ROHDE & SCHWARZ SMR30 REPAIR
 
A calibration by Custom-Cal is performed by engineers with extensive OEM experience. We have the expertise and the necessary standards to perform the ROHDE & SCHWARZ SMR30 Calibration, onsite calibration may be available. We specialize in quick turnaround times and we can handle expedited deliveries upon request.

Need another Signal Generator?
Shop for Comparable Products on our  used Signal Generator page

 
   ROHDE & SCHWARZ SMR30 (1104.0002.30)   Description / Specification:   Spec Sheet 
ROHDE & SCHWARZ SMR30 30 GHz CW, Signal or Synthesized Sweep Generator

The R&S SMR30 (1104.0002.30) 30 GHz CW, signal or synthesized sweep generator can be upgraded any time by means of options to give an AM/FM signal generator or a synthesized sweep generator featuring fast, fully synthesized, analog ramp sweep. Advanced frequency synthesis with fractional-N divider makes for low SSB phase noise and high spurious suppression, both of which are for example prerequisites for reliable receiver measurements. The crystal reference built in as standard ensures an accurate, low-drift output frequency. A high-quality pulse modulator has an on/off ratio is better than 80 dB, the rise/fall time shorter than 12 ns. Pulse widths of up to 25 ns are possible. Specifications. Frequency range: 1 GHz to 30 GHz (10 MHz to 30 GHz optional). Resolution: 1 kHz (0.1 Hz optional). Aging (after 30 days of operation): 1 × 10^–6/year <1 × 10^–7/year. SSB phase noise (f = 10 GHz, 10 kHz from carrier, 1 Hz bandwidth, CW, FM off): <–83 dBc. Maximum level: >+12 dBm (0.01 GHz to <1 GHz), >+8 dBm (1 GHz to <18 GHz), >+7 dBm (18 GHz to 20 GHz), >+11 dBm (>20 GHz to 27 GHz), >+9 dBm (>27 GHz to 30 GHz). Minimum level of all models: -20 dBm (underrange <-20 dBm). Resolution: 0.1 dB or 0.01 dB, selectable. Impedance: 50 ohm. SWR: <2. Options. SMR-B1 (1104.5485.02), OCXO Reference Oscillator. SMR-B3 (1104.5585.02), Frequency Resolution 0.1 Hz. SMR-B4 (1104.5685.02), Ramp Sweep. SMR-B5 (1104.3501.02), AM/FM/Scan Modulator. SMR-B11 (1104.4250.02), Frequency Extension 0.01 GHz to 1 GHz. SMR-B14 (1104.3982.02), Pulse Generator. SMR-B15 (1104.4989.02), RF Attenuator. SMR-B20 (1104.6381.02), Rear Connectors for RF, AF. SMR-B24 (1104.6100.02), IF Input DC to 700 MHz. SMR-B31 (1164.7910.02), Low Leakage. SMR-B17 (1104.5233.02), RF Attenuator. SMR-B20 (1104.6381.02), Rear Connectors for RF, AF. SMR-B24 (1104.6100.02), IF Input DC to 700 MHz. SMR-B31 (1164.7910.02), Low Leakage.



 

Standard Calibration $730.00 *
Click on Logo for More Prices
*This is a Web introductory price for one calibration of the ROHDE & SCHWARZ SMR30. Price does not in most cases include measurement performance data. Pricing does include NIST traceable calibration and issue of a calibration certificate and calibration label. Pricing may vary slightly due to volume and location of laboratory supporting calibration. Volume pricing may apply. On-site fees may apply depending on logistics, location and volume of work to be completed during the visit.


Related Bench Equipment Terms and Definitions. For a complete list go to our  Terms and Definitions Page.

Available Gain
Available Gain is the ratio, at a specific frequency, of power available from the output to the power in from the source.

Decibel (dB)
A unit of measurement of power which indicates relative power. A -10 dB means a reduction in power by 10 times, -20 dB means another 10 times or 100 times overall, -30 means another 10 times or 1000 times overall and so on.

Mismatch Uncertainty
Mismatch Uncertainty is caused by re-reflections between one device (the source) and the device that follows it (the load).

Pulse Power
Pulse Power, the energy transfer rate is averaged over the pulse width. Pulse width is considered to be the time between the 50 percent risetime/falltime amplitude points. Pulse power averages out any aberrations in the pulse envelope such as overshoot or ringing.

Please contact us for your ROHDE & SCHWARZ SMR30 CALIBRATION and/or ROHDE & SCHWARZ SMR30 30 GHz CW, Signal or Synthesized Sweep Generator REPAIR
I'm interested in: 
Calibration Type (Select one):
Repair Information:
 Serial Number:

 Is there any physical damage?  
 If yes, describe:


What is the description of the problem?

How/when did the problem start?


 (*) Required Fields    For formal quote please fill in all fields.
Company:
From (Email):*
Contact Name:*
Country:*
Address 1:
Address 2:
City:
State/Territory/Province: *
Zip/Postal Code:
Phone:*

Comment: