AMPROBE ACD-14 PLUS CALIBRATION and AMPROBE ACD-14 PLUS REPAIR

 
A calibration by Custom-Cal is performed by engineers with extensive OEM experience. We have the expertise and the necessary standards to perform the AMPROBE ACD-14 PLUS Calibration, onsite calibration may be available. We specialize in quick turnaround times and we can handle expedited deliveries upon request.

 

 
   AMPROBE ACD-14 PLUS   Description / Specification:    
AMPROBE ACD-14 PLUS 600 Amp TRMS Clamp Type Meter

The Amprobe ACD-14 PLUS Digital Clamp Meter is the perfect choice for both HVAC and electrical applications due to its versatile set of features. Electricians will find it’s thin, light and versatile with thinner jaws than standard clamp meters (only 0.4”/10mm thick). Its ability to measure temperature, capacitance, and microamps are important features for HVAC technicians. The ACD-14 PLUS meter offers thinner jaws over standard clamp meters, allowing access to tight measurement areas and still accommodating conductors up to 25 mm.
Specifications / Features.

True-rms.
AC Voltage: 4.000 V, 40.00 V, 400.0 V, 600 V.
DC Voltage: 400.0 mV, 4.000 V, 40.00 V, 400.0 V, 600 V.
AC Current: 40.00 A, 400.0 A, 600 A.
Resistance: 400.0 Ω, 4.000 kΩ, 40.00 kΩ, 400.0 kΩ, 4.000 MΩ, 40.00 MΩ.
Capacitance: 500.0 nF, 5.000 µF, 50.00 µF, 500.0 µF, 3000 µF.
Frequency: 40 Hz to 400 Hz with Jaw, 10 Hz to 100 kHz with test leads.
Temperature: -4 °F to 999 °F (-20 °C to 537 °C).



 



Related Bench Equipment Terms and Definitions. For a complete list go to our  Terms and Definitions Page.

Channel Bandwidth
Channel Bandwidth is the bandwidth over which power is measured. This is usually the bandwidth in which almost all of the power of a signal is contained.

Jitter
Jitter in technical terms is the deviation in or displacement of some aspect of the pulses in a high-frequency digital signal. Jitter is the time variation of a periodic signal in electronics and telecommunications, often in relation to a reference clock source. Jitter may be observed in characteristics such as the frequency of successive pulses, the signal amplitude, or phase of periodic signals. Jitter is a significant, and usually undesired, factor in the design of almost all communications links (e.g., USB, PCI-e, SATA, OC-48). In clock recovery applications it is called timing jitter.

Overshoot
Overshoot is the distortion that follows a major transition; the difference between the peak power point and the pulse-top amplitude computed as a percentage of the pulse-top amplitude.

Rise Time
Rise time refers to the time required for a signal to change from a specified low value to a specified high value, usually 10 and 90 percent of pulse-top amplitude (vertical display is linear power).


Please contact us for your AMPROBE ACD-14 PLUS CALIBRATION and/or AMPROBE ACD-14 PLUS 600 Amp TRMS Clamp Type Meter REPAIR

I'm interested in: 
Calibration Type (Select one):


Repair Information:
 Serial Number:

 Is there any physical damage?  
 If yes, describe:


What is the description of the problem?

How/when did the problem start?


 (*) Required Fields    For formal quote please fill in all fields.
Company:
From (Email):*
Contact Name:*
Country:*
Address 1:
Address 2:
City:
State/Territory/Province: *
Zip/Postal Code:
Phone:*

Comment: