|
Initialization Error (AttInitialize(), 1) |
|
|
Error during attenuator initialization. No ready message from attenuator DSP
after reset |
|
Initialization Error (AttInitialize(), 2) |
|
|
Error during attenuator initialization. No ready message from attenuator DSP
after init motor |
|
Initialization Error (AttInitialize(), 4) |
|
|
Error during attenuator initialization. No ready message from attenuator DSP
after find index |
|
Initialization Error (AttInitialize(), 8) |
|
|
Error during attenuator initialization. No ready message from attenuator DSP
after move to min position) |
|
Initialization Error (AttMovePos(zeroPos), 8)) |
|
|
No ready message from attenuator DSP after moving to zero position taken from
caldata |
|
Initialization Error (CalData CRC wrong: crc1, stored: crc2!)) |
|
|
The checksum stored in the caldata does not match the calculated checksum (crc1
= calculated checksum) |
|
|
The checksum stored in the caldata does not match the calculated checksum (crc2
= checksum read from caldata) |
|
Initialization Error (Calibration Data Invalid, 0) |
|
|
The calibration data was tagged as invalid before it was loaded on to the module |
|
Initialization Error (CalOptZeroMeas, 1) |
|
|
Error in optical zero measurement |
|
Initialization Error (DspMainCalcKFactor failed, -1) |
|
|
DSP K factor calibration failed, no TCFS (according to caldata) |
|
Initialization Error (DspMainCalcKFactor failed, 1) |
|
|
DSP K factor calibration failed, error when calibrating TCFS |
|
Initialization Error (DspMainCalcKFactor failed, 2) |
|
|
DSP K factor calibration failed, DSP sweep failed |
|
Initialization Error (DspMainCalcKFactor failed, 4) |
|
|
DSP K factor calibration failed, laser safety |
|
Initialization Error (DspMainWriteCaldata(), 5) |
|
|
Error while writing cal data to DSP, tried to access invalid array position |
|
Initialization Error (DspMainWriteCaldata(), 6) |
|
|
Error while writing cal data to DSP, wrong dimension |
|
Initialization Error (DspMainWriteCaldata(), 7) |
|
|
Error while writing cal data to DSP, unknown type found in variable array |
|
Initialization Error (DspMainWriteCaldata(), 8) |
|
|
Error while writing cal data to DSP, wrong parameter when trying to access one
of the DSPs cal arrays |
|
Initialization Error (Firmware CRC wrong: crc1, stored: crc2!) |
|
|
The checksum stored in the firmware does not match the calculated checksum (crc1
= calculated checksum) |
|
|
The checksum stored in the firmware does not match the calculated checksum (crc2
= checksum read from caldata) |
|
Initialization Error (HwAccessInit, 1) |
|
|
Error setting DAC |
|
Initialization Error (InitDacs, 1) |
|
|
Error setting DAC |
|
Initialization Error (InstSettingInit, 2) |
|
|
Error creating semaphore |
|
Initialization Error (LaserEEPROMInit, 1) |
|
|
Error reading laser EEPROM |
|
Initialization Error (MainEEPROMInit, 1) |
|
|
Error reading main EEPROM |
|
Initialization Error (MotorSelfCali failed, -1) |
|
|
Motor self calibration failed |
|
Initialization Error (MotorZero, 1) |
|
|
DSP motor zero not finished in time |
|
Initialization Error (OptZero, -1) |
|
|
Optical zero disabled in caldata |
|
Initialization Error (OptZero Opc, 16) |
|
|
Timeout while waiting for laser diode (16) and thermopositioner (64) to settle
while preparing optical zero measurement, waiting for laser diode |
|
Initialization Error (OptZero Opc, 64) |
|
|
Timeout while waiting for laser diode (16) and thermopositioner (64) to settle
while preparing optical zero measurement, waiting for thermopositioner |
|
Initialization Error (TASK_TIMEOUT, id1)) |
|
|
An init task has not finished in time (id1 = task name) |
|
Initialization Error (TASK_VERIFY, id1, id2) |
|
|
A task could not be started (id1 = task name) |
|
|
A task could not be started (id2 = maximum available memory) |
|
Initialization Error (Tcfs Amplifier Calibration failed, 0) |
|
|
The calibration of the tuning control feedback system amplifier has failed |
|
Initialization Error (TcfsAdpEEPROMInit, 1) |
|
|
Error reading tuning control feedback system adapter board EEPROM |
|
Initialization Error (TcfsEEPROMInit, 1) |
|
|
Error reading tuning control feedback system EEPROM |
|
Initialization Error (Tcfs temperature not settled, 0) |
|
|
Temperature has not settled at the tuning control feedback system |
|
Initialization Error (TmpCalDataInit, 1) |
|
|
Error accessing caldata |
|
Initialization Error (UpPiezoEnable, 1) |
|
|
Over current |