Keysight (Agilent) 83496B REPAIR and Keysight (Agilent) 83496B CALIBRATION
 
Custom-Cal has a high success rate in the repair of the Keysight (Agilent) 83496B. A calibration by Custom-Cal is performed by engineers with extensive OEM experience. We have the expertise and the necessary standards to perform the Keysight (Agilent) 83496B Calibration, onsite calibration may be available. We specialize in quick turnaround times and we can handle expedited deliveries upon request.

Need another Fiber Optic Instrumentation?
Shop for Comparable Products on our  used Fiber Optic Instrumentation page

 
   Keysight (Agilent) 83496B   Description / Specification:   Spec Sheet 
Keysight (Agilent) 83496B Clock Recovery Module with Phase Noise Analysis

The Agilent 83496B Clock Recovery Module with Phase Noise Analysis provides increased eye-mask and jitter measurement accuracy with breakthrough performance in clock recovery circuitry. It provides ideal performance for waveform analysis with the 86100 Digital Communications Analyzer and can derive a clock from signals with rates as low as 50 Mb/s-14.2 GB/s, and any rate in between. At under 300 femtoseconds rms, the residual jitter of the output clock is virtually negligible, allowing accurate measurements of very low levels of signal jitter. Specifications. Operating range: 50 Mb/s to 7.1 Gb/s(with Option 200: 50 Mb/s to 14.2 Gb/s). Residual jitter (jitter free input): < 300 fs rms. Loop BW: 270 kHz or 1.5 MHz (with Option 300: 15 kHz to 10 MHz or fixed ratio of data rate/N). Wavelength range: 780 to 1330 nm MMF (62.5 um), Option 101 1250 to 1620 nm SMF (9 um). Options. Option 100: Electrical differential or single-ended clock recovery 50 Mb/s to 7.1 Gb/s. Option 101: Optical single mode 1250 to 1620 nm and multimode 780 to 1330 nm clock recovery 50 Mb/s to 7.1 Gb/s. Option 200: Increase operating range to 14.2 Gb/s. Option 201: Operating range of either Option 100 or Option 101 is set to be 7.1 to 14.2 Gb/s. Option 300: Add Golden PLL (tunable loop bandwidth capability).



 

Standard Calibration $885.00 *
Click on Logo for More Prices
*This is a Web introductory price for one calibration of the Keysight (Agilent) 83496B. Price does not in most cases include measurement performance data. Pricing does include NIST traceable calibration and issue of a calibration certificate and calibration label. Pricing may vary slightly due to volume and location of laboratory supporting calibration. Volume pricing may apply. On-site fees may apply depending on logistics, location and volume of work to be completed during the visit.


Related Optical Terms and Definitions. For a complete list go to our  Terms and Definitions Page.

Bandwidth
Bandwidth is the difference between the upper and lower frequencies in a contiguous set of frequencies within which a fiber optic component, link or network will operate.

Extinction Ratio (ER)
Extinction Ratio is the ratio of two optical power levels, of a digital signal generated by an optical source, (example a laser diode), where P1 is the optical power level generated when the light source is "on," and P0 is the power level generated when the light source is "off." The extinction ratio may be expressed as a fraction, in dB, or as a percentage.

Optical Signal-to-noise Ratio (OSNR)
Optical Signal-to-noise ratio is the ratio between the signal power and the noise power in a given bandwidth. Most commonly a reference bandwidth of 0.1 nm is used. This bandwidth is independent from the modulation format, the frequency and the receiver. For instance a OSNR of 20dB/0.1nm could be given, even the signal of 40 GBit DPSK would not fit in this bandwidth. OSNR is measured with a Optical Spectrum Analyzer. It is generally measured at the wavelength of interest.

Repeatability
Repeatability is the variation in a number of repeated measured quantities when measurement conditions are changed and restored. The value corresponds to half the spread between the minimum and maximum value measured.

Wavelength Repeatability
Wavelength Repeatability is the random uncertainty in reproducing a wavelength after detuning and re-setting the wavelength. The wavelength repeatability is ± half the span between the maximum and the minimum value of all actual values of these wavelengths. Example test condition: uninterrupted TLS output power, constant power level, temperature within operating temperature range, coherence control off, short time span. Note: NOTE The long-term wavelength repeatability can be obtained by taken the wavelength repeatability and wavelength stability into account.

Please contact us for your Keysight (Agilent) 83496B REPAIR and/or Keysight (Agilent) 83496B Clock Recovery Module with Phase Noise Analysis CALIBRATION
I'm interested in: 
Calibration Type (Select one):
Repair Information:
 Serial Number:

 Is there any physical damage?  
 If yes, describe:


What is the description of the problem?

How/when did the problem start?


 (*) Required Fields    For formal quote please fill in all fields.
Company:
From (Email):*
Contact Name:*
Country:*
Address 1:
Address 2:
City:
State/Territory/Province: *
Zip/Postal Code:
Phone:*

Comment: