Keysight (Agilent) 6675A REPAIR and Keysight (Agilent) 6675A CALIBRATION

 
Custom-Cal has a high success rate in the repair of the Keysight (Agilent) 6675A. A calibration by Custom-Cal is performed by engineers with extensive OEM experience. We have the expertise and the necessary standards to perform the Keysight (Agilent) 6675A Calibration, onsite calibration may be available. We specialize in quick turnaround times and we can handle expedited deliveries upon request.

Need another DC Power Supply?
Shop for Comparable Products on our
 used DC Power Supply page

 
   Keysight (Agilent) 6675A   Description / Specification:    
Keysight (Agilent) 6675A 120V 18A Single Output System DC Power Supply

The Agilent 6675A is a 0-120 VDC / 0-18 A, Single-Output 2000 W, Remote Sensing, (GPIB) Power Supply. Features, DC Floating Voltage: Output terminals can be floated up to ±240 Vdc from chassis ground. Output Common-Mode Noise Current: (to signal ground binding post) 500 µA rms, 4 mA peak-to-peak. Remote Sensing: Up to half the rated output voltage can be dropped in each load lead. The drop in the load leads subtracts from the voltage available for the load. Command Processing Time: Average time required for the output voltage to begin to change following receipt of digital data is 20 ms for the power supplies connected directly to the HP-IB. Output Programming Response Time: The rise and fall time (10/90% and 90/10%) of the output voltage is less than 15 ms. The output voltage change settles within 1 LSB (0.025% x rated voltage) of final value in less than 60 ms. Modulation: (Analog programming of output voltage and current). Input Signal: 0 to –4V for voltage, 0 to 7 V for current. Input Impedance: 30 k Ohm or greater. Input Power: 3,800 VA, 2,600 W at full load; 170 W at no load. Specifications. Output voltage: 0 to 120 V. Output current: 0 to 18 A. Programming accuracy (at 25° C ±5° C) Voltage: 0.04% + 120 mV. Programming accuracy (at 25° C ±5° C) Current: 0.1% + 12 mA. Ripple and noise (from 20 Hz to 20 MHz) Voltage: 1.9 mV (RMS), 16 mV (peak-peak). Ripple and noise (from 20 Hz to 20 MHz) Current: 12 mA (RMS). Readback accuracy at 25° C ±5° C (percent of reading plus fixed): Voltage 0.05% + 180 mV / ±Current 0.1% + 18 mA. Load and line regulation Voltage: 0.002%+ 4 mV. Load and line regulation Current: 0.005%+ 1 mA. Transient Response Time: Less than 900 µs for the output voltage to recover 100 mV following a change in load from 100% to 50%, or 50% to 100% of the output current rating of the supply.



 

Standard Calibration $105.00 *
Click on Logo for More Prices
*This is a Web introductory price for one calibration of the Keysight (Agilent) 6675A. Price does not in most cases include measurement performance data. Pricing does include NIST traceable calibration and issue of a calibration certificate and calibration label. Pricing may vary slightly due to volume and location of laboratory supporting calibration. Volume pricing may apply. On-site fees may apply depending on logistics, location and volume of work to be completed during the visit.


Related Bench Equipment Terms and Definitions. For a complete list go to our  Terms and Definitions Page.

Available Gain
Available Gain is the ratio, at a specific frequency, of power available from the output to the power in from the source.

Decibel (dB)
A unit of measurement of power which indicates relative power. A -10 dB means a reduction in power by 10 times, -20 dB means another 10 times or 100 times overall, -30 means another 10 times or 1000 times overall and so on.

Mismatch Uncertainty
Mismatch Uncertainty is caused by re-reflections between one device (the source) and the device that follows it (the load).

Pulse Power
Pulse Power, the energy transfer rate is averaged over the pulse width. Pulse width is considered to be the time between the 50 percent risetime/falltime amplitude points. Pulse power averages out any aberrations in the pulse envelope such as overshoot or ringing.


Please contact us for your Keysight (Agilent) 6675A REPAIR and/or Keysight (Agilent) 6675A 120V 18A Single Output System DC Power Supply CALIBRATION

I'm interested in: 
Calibration Type (Select one):


Repair Information:
 Serial Number:

 Is there any physical damage?  
 If yes, describe:


What is the description of the problem?

How/when did the problem start?


 (*) Required Fields    For formal quote please fill in all fields.
Company:
From (Email):*
Contact Name:*
Country:*
Address 1:
Address 2:
City:
State/Territory/Province: *
Zip/Postal Code:
Phone:*

Comment: